Click Here

 

They are making a number of great points about A Step-by-Step Guide to Installing a Bathtub overall in the content down the page.

Mounting a tub isn't specifically rocket science, but it does call for solid plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably difficult task. If the old bathtub is readily available, the job can move rapidly; if you have to open a wall to remove the old tub and position the brand-new tub, the job is a lot harder. In either case, the task is within a home handyman's abilities, although you will certainly require an assistant to leave the old bathtub and also embeded in the new one. Ensure you have certified yourself for the job and also fit attempting it. Rather than working with a service provider to take over a halfway-completed task, it is far better to think about employing one prior to you begin. Opportunities are you may require an expert plumber to make tube links.
This post will assist you mount a brand-new bathtub in your restroom if you have currently purchased a new bathtub and also don't need to alter the setup of your previous supply of water pipelines.
Your devices as well as material checklist should comprise the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipe Caps


 

Removing Old Taps

If you require to replace old taps with new ones as a part of your setup, then the first thing you ought to do is separate the water system. After doing so, activate the faucets to drain any type of water staying in the system. The process of removing the existing taps can be fairly problematic as a result of the restricted gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will certainly come from the pipes. As soon as the supply pipes have been eliminated, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from transforming throughout this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
Before carrying on to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.

 

 

Fitting New Taps

If the tails of the new taps are plastic, after that you will require a plastic connector to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will need lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin making certain that the washers remain in place in between the tap and the sink. Safeguard the tap in place with the producer supplied backnut. When the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap connectors. The former kind needs to be linked to the tap ends initially, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.

 

 

Mounting the Tub

Using both wooden boards under its feet, place the tub in the called for position. The wooden boards are practical in evenly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 small factors.
The following goal is to make sure that the bath tub is leveled all round. This can be attained by inspecting the spirit level as well as changing the feet on the tub up until the level reviews degree.
To mount taps, fit the bottom of the furthest versatile faucet connector to the proper supply pipeline by making a compression join; after that do the very same for the various other faucet.
Activate the water supply and also inspect all joints and brand-new pipework for leaks and tighten them if essential. Fill up the bath tub and also check the overflow outlet and also the regular outlet for leaks.
Ultimately, deal with the bath paneling as described in the supplier's instruction manual. Tiling and also securing around the bathtub must wait till the bathtub has been made use of at least once as this will certainly resolve it right into its final position.

 

 

Getting ready for the Installment

To start with, the sustaining structure supplied with the bath should be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the tub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its final position.

 

 

Tiling Around the Bathtub

In the location where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack a stiff seal, triggering the water to penetrate the wall surface between the bath and the tiling, leading to difficulties with moisture and feasible leakages to the ceiling below.
You can select from a selection of coloured sealers to blend in your components and fittings. They are offered in tubes as well as cartridges, and also can securing voids up to a size of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly load the bath tub with water prior to sealing, to permit the motion experienced when the tub remains in usage. The sealer can crack fairly very early if you do not take into consideration this activity prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily readily available on the market. It is advisable to fit the floor tiles using waterproof or water resistant glue and cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I recently found that piece about Installing A Bathtub while looking around the web. Do you know about another individual who is fascinated with Installing A Bathtub? Please feel free to promote it. We value reading our article about Tools You Need to Install a New Bathtub .

Book Today!